本地伺服器
本地伺服器是玩家在本地網絡（比如家庭wifi）中建立的伺服器，建立伺服器的玩家擁有對這個伺服器的完全控制權。
使用本地伺服器的原因有很多。它能夠讓你做到：
- 和朋友一起遊玩時不受別人打擾
- 遊玩官方伺服器中沒有的地圖
- 用管理員指令和工具對地圖進行測試
- 以及更多！
然而，建立本地伺服器仍然有許多缺點。你需要一些特殊的方法來讓你的朋友加入你的伺服器，並且相比起官方伺服器，其他玩家在你建立的本地伺服器中會遭受更多網絡的影響。注意本地伺服器只會在本地保存過圖記錄，這意味著你在本地伺服器中完成地圖並不會將記錄同步到官方伺服器。
建立和加入本地伺服器
在新版DDNet客戶端中，建立本地伺服器非常簡單。
- 找到遊戲的開始菜單
- 點擊「運行伺服器」
- 一個黑底白字的命令行窗口會彈出（這可能需要一小段時間）。從這個窗口中複製rcon的密碼（也可以在遊戲路徑的autoexecserver.cfg文件中查看並設置）。
- 打開遊戲客戶端的瀏覽伺服器界面，在上方選擇區域網，刷新後即可加入。
- 進入遊戲後，按f2打開伺服器控制台rcon，然後輸入密碼來獲得管理員指令的使用權限。
However, this only allows players on your local network to join. In other words - nobody else except you can join this LAN server online. To allow players to join online, you'll have to go through more steps.
Setting Up Your LAN Server for Online Play
This next step requires you to port forward, which depends on the brand and type of router you have.
- Port forward the UDP port 8303 through your router.
- The easiest way to do this is to simply search "how to port forward" in your preferred search engine. This process usually requires you to log into your router interface, which, again, varies per household.
- Make sure to choose the UDP setting, and not the TCP or the TCP/UDP setting.
- You can forward a port other than 8303 if you set up the desired port using
sv_portin your server autoexecutable. However, the default port is 8303 for DDNet. So, if you're not sure what you're doing, just forward port 8303.
- If you'd like your server to show up on the Internet tab, use the server setting
sv_register 1, either in the f2 console or in the server autoexecutable. Note that this will make your IP publicly viewable if you host the server from your home network. So, use at your own risk.
Some ISPs might not provide you with a full native IPv4 address, but instead use carrier-grade NAT, and will thus not support forwarding ports. In this case you can't make your LAN server available for online play.
Setting Up on Linux Server
Linux
Method 1 (Compiling server) [Show/Hide] |
1.Update the Server
2. Install git
3. Make a directory
3. Clone the repository from Github
4. Install all required dependencies
5. Go into ddnet folder
5. Compile DDNet
6. Open Server
7. forward a port to the server (default is 8303) 8. Connect via Client on the IP
9.Play More Information are available at https://github.com/ddnet/ddnet |
Method 2 (Using precompiled binaries) [Show/Hide] |
| 1. Download binaries from DDNet download page
2. Extract into folder 3. Open Server
4. Forward a port to the server (default is 8303) 5. Connect via Client on the IP
6. Play |
More Information about Port forwarding are available at http://portforward.com/
Server Settings and Maps
Everything settings and map-wise can be found in your Teeworlds folder.
- On Windows, you can find it in AppData/Roaming/Teeworlds.
- On Linux, you can find it in (insert location here).
- On Mac, you can find it in (insert location here).
Server Autoexecutables
Server autoexecutables are files containing server settings that are automatically run every time you start your server. For example, this can be helpful if you want to keep a single rcon password to log in with every time.
To create an autoexecutable, navigate to your Teeworlds folder (not your DDNet folder!), and create a file by the name of "autoexec_server.cfg". Make sure it is a .cfg extension file and not a .txt file or anything similar.
To add commands, simply edit the autoexec_server.cfg file and add each command on a new line. Here are examples of commonly used commands:
- sv_rcon_password <rcon password>
- sv_password <password to join>
- sv_name <server name>
- sv_register 1 (shows the server on the Internet tab)
- sv_test_cmds 1 (allows the use of cheat commands)
Server Maps
Server maps can be found in Teeworlds/maps. To load a map ingame, use the server command sv_map <mapname>.
See also
- DDNet Server configuration in Arch Wiki
- https://github.com/ddnet/ddnet-maps - DDNet maps repository