Hammerfly: Difference between revisions
mNo edit summary |
|||
| Line 3: | Line 3: | ||
To hammer fly: | To hammer fly: | ||
* | * Stack 2 tees on top of each other (use a wall to line up) | ||
* | * The lower tee continuously hammers the upper tee | ||
* | * The upper tee (the ‘driver’) hooks the lower tee | ||
The hammer hits propel the driver upwards | The hammer hits propel the driver upwards | ||
| Line 11: | Line 11: | ||
The continuous hook: | The continuous hook: | ||
* | * Pulls the hammering tee upwards | ||
* | * Keeps the two tees into hammer range | ||
This way you can fly upwards indefinitely. | This way you can fly upwards indefinitely. | ||
| Line 30: | Line 30: | ||
Whenever you don’t have a wall to line up in a tower: | Whenever you don’t have a wall to line up in a tower: | ||
* | * Choose a tee to drive | ||
* | * Have the driving tee jump over the other tee | ||
* | * Start the usual hammerfly cycle | ||
[[File:Hammerfly-free.mp4|thumb]] | [[File:Hammerfly-free.mp4|thumb]] | ||
| Line 52: | Line 52: | ||
If the driver still has double jump available, you could: | If the driver still has double jump available, you could: | ||
* | * Stop the hammer fly cycle shortly | ||
* | * Have the driver double jump to cancel the falling speed | ||
* | * Start the hammer fly cycle again | ||
Without double jump, you can: | Without double jump, you can: | ||
* | * Stop the hammering | ||
* | * Have the driver hook the lower tee again and again to bump into each other | ||
The bumping will slow down the drop significantly. This way you can start the cycle any time you want. | The bumping will slow down the drop significantly. This way you can start the cycle any time you want. | ||
Revision as of 18:45, 21 January 2021
Hammer fly is the most common flight technique for 2 tees.
To hammer fly:
- Stack 2 tees on top of each other (use a wall to line up)
- The lower tee continuously hammers the upper tee
- The upper tee (the ‘driver’) hooks the lower tee
The hammer hits propel the driver upwards
The continuous hook:
- Pulls the hammering tee upwards
- Keeps the two tees into hammer range
This way you can fly upwards indefinitely.
Timing
Spamming the hammer and hook won’t get you very high.
As the hammering tee, try to hammer whenever you just bounced off the other tee.
As the driver, never let go of the other tee in the air. Hooking every second hammer hit the lower tee does is a good rhythm.
Without Lining Up
Whenever you don’t have a wall to line up in a tower:
- Choose a tee to drive
- Have the driving tee jump over the other tee
- Start the usual hammerfly cycle
Driving
Driving allows the driving tee to direct the hammer fly to the side. When done well, this allows for horizontal flight.
As the driver, drive by moving in the desired direction directly after you got hit by the hammer.
Start with very light movement. The further you move each hit, the more horizontal, but also unstable the hammer fly will get.
Dropping While Hammer flying
Some parts require you to drop a bit during a hammer fly.
If the driver still has double jump available, you could:
- Stop the hammer fly cycle shortly
- Have the driver double jump to cancel the falling speed
- Start the hammer fly cycle again
Without double jump, you can:
- Stop the hammering
- Have the driver hook the lower tee again and again to bump into each other
The bumping will slow down the drop significantly. This way you can start the cycle any time you want.
Note however, that you want to have strong hook as the driver for this, else the bumping might not work as well.
Kinta Fly
Kinta fly (or just ‘kinta’) is a special but much harder variant of hammer fly. It is usually done below a ceiling and allows horizontal flight in much tighter space.
For kinta, both tees have to move in the desired direction at the same time. Don’t move continuously, but instead like you would move while driving.
What you want to achieve is that both tees stay above each other. Note that you might have to adapt your hammering rhythm.
To initiate kinta successfully, start moving at the same time. Usually you start moving in the direction once the upper tee is near the ceiling.
Speed fly
Speed fly can be attempted during a usual hammer fly to reach high vertical velocity.
Initiate speed fly as the driver by double jumping just before you will get hammered. If you got the timing, you will suddenly gain a lot of height than usual on the hammer hit.
To keep the speed up, the hammering tee always has to hammer just before bumping into the upper tee, which would break it.
Pretty much every time window for this trick is very narrow.